Ocing q6600 with asus p5qd turbo

[archspace]

---

note: i have covered the basics of ocing like getting a good cooler etc.

I just want to have my config checked since im getting BSOD after stress testing using prime 95 with blend tests.

Settings:

cpu voltage 1.4
cpu gtl reference auto (should i touch this?)
cpu pll voltage 1.5 (not sure)
fsb termination voltage 1.32 (not sure)
dram voltage 2.1 (not sure)
nb voltage auto (shoudl i make adjustments on this?)
sb voltage auto (shoudl i make adjustments on this?)
pcie sata voltage auto (shoudl i make adjustments on this?)


pls help and let me know if there is any other info that you need to know in order to help me thanks in advance.

note: stress testing right now and its working so far. waiting for the next 2-3 hours for stability

[archspace]

update: after 12 hours of testing. steady ko at 3.0 will try to push it further later.

[werty]

how did u manage to set procie voltage at 1.4v already? coz getting to 3Ghz can be done with a bit less volts than that..

[keropi]

note: i have covered the basics of ocing like getting a good cooler etc.

I just want to have my config checked since im getting BSOD after stress testing using prime 95 with blend tests.

Settings:

cpu voltage 1.4
cpu gtl reference auto (should i touch this?)
cpu pll voltage 1.5 (not sure)
fsb termination voltage 1.32 (not sure)
dram voltage 2.1 (not sure)
nb voltage auto (shoudl i make adjustments on this?)
sb voltage auto (shoudl i make adjustments on this?)
pcie sata voltage auto (shoudl i make adjustments on this?)


pls help and let me know if there is any other info that you need to know in order to help me thanks in advance.

note: stress testing right now and its working so far. waiting for the next 2-3 hours for stability

Dili ko swito sa imo mobo but i guess only the names differ. You only need to adjust Vcore, Vdimm, VTT/Vmch. That's Vcpu, Vram and Vnb on your board.. All other voltages are minor and only need to be adjusted if thus proven.. 1 notch on pll sometimes..

[archspace]

how did u manage to set procie voltage at 1.4v already? coz getting to 3Ghz can be done with a bit less volts than that..

i lowered it to 1.38 and it worked. 2 hours na steady and ga games ko. no bsod. im trying to push it to 3.4 with 1.45 volts. bsod nko dli ko sure unsa pay ako i tweak ani.

voltage lng ako g usab ron. 1.45 and trying to stabilize 3.3. when i tried 3.4 with 1.45 volts, bsod nko.

[werty]

only increase voltage if instability occurs- unsay memory nmo gamit? pila volts? basin maoy nag limit sa imo overclock. 3.4-3.6 is easy for this procie.

[archspace]

only increase voltage if instability occurs- unsay memory nmo gamit? pila volts? basin maoy nag limit sa imo overclock. 3.4-3.6 is easy for this procie.

i think ang memory jud. kingston ram ni. im sure dli ni oc quality.
running at 3.3 now with 1.44 volts 40 minutes oc testing atm. my temp is high 70c. haha okay rani nga temp or basin init na kaau ni? i lower nlng nko sa 3.2 if init ra.

[werty]

murag init ra jud na. taas ra nang 1.44 i think for that speed. try changing multiplier sa imo memory, set it as low as possible and try increasing fsb w.o changing voltage as see asa limit b4 u need to increase volts to procie again.

[archspace]

murag init ra jud na. taas ra nang 1.44 i think for that speed. try changing multiplier sa imo memory, set it as low as possible and try increasing fsb w.o changing voltage as see asa limit b4 u need to increase volts to procie again.

bro imong pasabot multiplier sa cpu? wla man ko nkita multiplier sa memory gud. clarohon lng nko. x9 ako multiplier g gamit ron.

[werty]

memory divider diay... or kanang ma set nmo ang memory to DDR400 or DDR800 something-set to lowest available.