P5PE-VM with Corsair CMX1024-3200C2

[regilsolon]

---

Ako board is Asus P5PE-VM.. naka acquire ko ug 2 x 1gig Corsair CMX1024-3200C2(XMS3200 1024MB 400MHz CL2). Ig start nako sa pc, di man maka dayon ug sud sa OS.. mo reboot ra cge.. Unsa probs ani, incompatibility? Pa lecture nya ko mga master.. hehe

i hope it helps this one bro.


Troubleshooting Tips for DDR-400 (XMS-3200C2)
Tested Settings for this Module: Speed: 25MHz Latency: 2-3-3-6-2T Voltage: 2.75


My system supports DDR400 memory, but when I install my Corsair DDR400 module the system will not post.
Many systems will indeed support DDR 400 memory. However, if for example your system came with a 533 FSB CPU you may be limited to DDR333 memory until you upgrade your CPU to an 800 Front Side Bus (FSB) CPU provided your system will support a faster CPU. The following guidelines may help with this: If the FSB of your CPU is 400 For Intel and 100 MHz for AMD, the memory speed supports only DDR 266. If the FSB of your CPU is 533 For Intel and 133/166 MHz for AMD, the memory speed supports DDR 266/333 If the FSB of your CPU is 800 MHz for Intel and 200 MHz for AMD, the memory speed supports DDR 333/400


Why are the timings shown in the SPD set to CAS 3?
All of our XMS-3200C2 will have their SPD set to JEDEC defined values for the specific memory IC used to make that part. This is done to ensure maximum compatibility with a wide variety of motherboards. The tested settings Cass 2-3-3-6 for Intel and Cass 2.5-3-3-6 for AMD need to be manually set in the BIOS.

[werty]

try this

*reset/clear cmos, restore default cmos settings, relax memory timings(overrated kaayo imo memory for your system)
*insert 1 memory module, then test with memtest86+ test# 5 about 3 passes... if success insert the other module and repeat test...if 1st module fails test, test the other one.
*if both ok, then boot into windows, test with prime95 or stressprime95...

[regilsolon]

^^ the @ts say : Ig start nako sa pc, di man maka dayon ug sud sa OS.. mo reboot ra cge

[BackBeat]

i hope it helps this one bro.


Troubleshooting Tips for DDR-400 (XMS-3200C2)
Tested Settings for this Module: Speed: 25MHz Latency: 2-3-3-6-2T Voltage: 2.75

Why are the timings shown in the SPD set to CAS 3?
All of our XMS-3200C2 will have their SPD set to JEDEC defined values for the specific memory IC used to make that part. This is done to ensure maximum compatibility with a wide variety of motherboards. The tested settings Cass 2-3-3-6 for Intel and Cass 2.5-3-3-6 for AMD need to be manually set in the BIOS.

Howto's for these steps? Not an OC'er.

[BackBeat]

try this

*reset/clear cmos, restore default cmos settings, relax memory timings(overrated kaayo imo memory for your system)
*insert 1 memory module, then test with memtest86+ test# 5 about 3 passes... if success insert the other module and repeat test...if 1st module fails test, test the other one.
*if both ok, then boot into windows, test with prime95 or stressprime95...

Ok boss, noted.

[BackBeat]

set kuno everything to Default sa imong BIOS(Load Defaults option)...

Wala pud nako na try ug load sa defaults.. suwayan lng pud nako nya..

[BackBeat]

ako nalang na imung heat spreaders kay nangita ko. hehe

eng eng eng.. haha sniper detected.

[regilsolon]

bro , unsay specs sa processor d i nimo ?

[butitoy]

easiest : > go asus.com.tw
download the manual

go to memory compatibility list.

[BackBeat]

bro , unsay specs sa processor d i nimo ?

P4 3.2 lng HT..