Help> Desktop di mu boot

[pktubthong]

---

Ngayo ko tabang pls..

Ako PC ba kai di mu boot. ig on nako igo ra mu siga for a second ang LEDs and spin ang fan, then mu off. Nya balik napud until ako pagngon AVR.

Specs:
i5-4460
Gigabyte z87m-d3h
8gb x 2 RAM
GTX 1060
st50f-esb

Steps done so far;
-Tried using 1 stick of RAM / Swap sticks
-Removed VC
-Reseated cables
-removed CMOS bat for 1 min then balik
-bypass UPS
-bypass AVR

mao ra japon. naa nag ingon MoBo, naa pud ingon PSU issue. kaso di ko sure.

sLamat sa tabang!

[RainRiku]

mu beep siya bro inig on nimo?

[Echelnalf]

When ni nag start? Tried them outside the case?

[pktubthong]

mu beep siya bro inig on nimo?

No beep sir.

- - - Updated - - -

When ni nag start? Tried them outside the case?

Gahapon lang jud.
Wala pa outside sa case kai di pako kapasalig bungkag sa wiring from psu.

[pulchra]

tan awa ang thermal basin init na sad ang cpu? try pa boot gawas sa case try lain psu. try e solod ang cpu / gpu/ram/psu sa lain na unit e exchange para ma isolate

[pktubthong]

tan awa ang thermal basin init na sad ang cpu? try pa boot gawas sa case try lain psu. try e solod ang cpu / gpu/ram/psu sa lain na unit e exchange para ma isolate

Mao pud lage ta boss. Kaso wa ko lain mobo ug psu para ma cross check.
As for sa procie, days old pa nuon. So murag d pud ngali mao sad.an. pero di jud ko ka ingon for sure.

[mikyAt]

most likely MOBO guba anah

[rayfloyd_170]

Ngayo ko tabang pls..

Ako PC ba kai di mu boot. ig on nako igo ra mu siga for a second ang LEDs and spin ang fan, then mu off. Nya balik napud until ako pagngon AVR.

Specs:
i5-4460
Gigabyte z87m-d3h
8gb x 2 RAM
GTX 1060
st50f-esb

Steps done so far;
-Tried using 1 stick of RAM / Swap sticks
-Removed VC
-Reseated cables
-removed CMOS bat for 1 min then balik
-bypass UPS
-bypass AVR

mao ra japon. naa nag ingon MoBo, naa pud ingon PSU issue. kaso di ko sure.

sLamat sa tabang!

TRY THESE:
1. clean the memory terminals (gold pins) with pencil eraser and also clean the memory slot kay mao na cause usually mag lose contact naay murag huga2w sa pins. if no effect go to 2.)
2. check ug clean imong heatsink basin clogged kaayo ug abog walay tarung na heat removal... you can also check the thermal paste. basin nag dry up na need to change with a good one like Arctic silver, etc... ayaw palit baratohon na thermal paste bati kaayo
3. imong videocard also clean the gold pins with pencil eraser.
4. if wala gihapon then try ug use another powersupply kana working in other units... if mo work gani kay you need to replace your PSU or have it repaired.. usually bad caps problem...
5. based on my exp kay usually memory problems rana or psu problem... mao you need to isolate each device one by one.
6. check also sa motherboard for any leaking capacitors.. , how old is your PC?


Good luck...

[pktubthong]

TRY THESE:
1. clean the memory terminals (gold pins) with pencil eraser and also clean the memory slot kay mao na cause usually mag lose contact naay murag huga2w sa pins. if no effect go to 2.)
2. check ug clean imong heatsink basin clogged kaayo ug abog walay tarung na heat removal... you can also check the thermal paste. basin nag dry up na need to change with a good one like Arctic silver, etc... ayaw palit baratohon na thermal paste bati kaayo
3. imong videocard also clean the gold pins with pencil eraser.
4. if wala gihapon then try ug use another powersupply kana working in other units... if mo work gani kay you need to replace your PSU or have it repaired.. usually bad caps problem...
5. based on my exp kay usually memory problems rana or psu problem... mao you need to isolate each device one by one.
6. check also sa motherboard for any leaking capacitors.. , how old is your PC?


Good luck...

MoBo, RAM, PSU kai 2 years
HDD is 5 months
Procie and VC kai 3 days

Unsa.on pag limpyu ang memory slot boss?
Prob pud jud nuon nang wa ko 2nd PSU para verify if mu andar babsa lain nga PSU.

Ako is ka RAM stick kai naai murag gamay nga stain. Mura taya ang color. Di man ma erase.
Pero ako gi try nga isa ra ka RAM, kaning wai stain. Di japon mu andar.

[nazaryl]

Hi Boss,

Hope makatabang ni.

Daghan au factors nanu dli m.on ang PC but most surely hardware issues jd ni xa.

1. Try take out all RAM sa ram slot and turn it on
- If nay beeps (assuming nay speaker imo mobo) that means your mobo is good. if ala, try to find a new mobo.
2. Try borrow a working RAM and check.
3. Take off Vcard and use onboard VGA / HDMI and turn on
- If mo on ni xa. Most likely compatibility issues sa mobo to vcard OR dli kaya sa imo PSU m.supply w/ the vcard.
4. Try re install the Processor
5. If anything above dli m.work, try change the PSU.
- assuming all pins are properly installed. like ang 4 pins sa mobo and im not sure if nay additional pins ang Vcard nimo.