Procie Temp Problem

[kidlovejeayanne]

---

butangi ug thermal paste ang imong proc brod, den e reinstall ang imong HS, basin luag.. den e clean lang sad imo casing basin abog na kaayo.. gamit ug blower..

[bolivar1985]

was able to find this while surfing the net.

your idle temp is in range, but temp of your procie when in used seems to be the questionable...

The maximum temperature of an Intel processor depends on the model but it normally range from 60-65 ° C for the Pentium 4, 50-65 ° for the Core models and 70 ° C for the Nehalem generation (i3/i5/i7 ). The mobile processors support up to 100 ° C approximately.

* You can have all the necessary information on Intel site:
o ARK | Your source for information on Intel products
* For example, the optimal temperature is 62 ° C for the Q6600:
o Intel® Core?2 Quad Processor Q6600 (8M Cache, 2.40 GHz, 1066 MHz FSB) with SPEC Code(s) SL9UM, SLACR
* and 72 °C for the Core i5 750:
o ARK | Your source for information on Intel products
* Beyond this value, a thermal protection of the system intervenes and brings the processor to its lowest frequency, blocking the CPU ratio to a minimum.
* If the temperature rises again, the CPU automatically shuts off, no thermal destruction is virtually impossible latest processors.

link:CPU is overheating- temperature problem

[eXpLoDe]

naa gyud ingon ani nga issue... i have encountered a lot... especially pentium d procie... dali ra kaayo mo init... akong g compare tanan procie ang naa gyud dali ra mo init... also you need a reliable thermal paste and a durable heatsink fan... power supply also will do...

[cursememore]

Thanks, Tried all ur suggestions na mga bro. Pero mao japon. Di man unta ni ingani, ni kalit man lang. Good as new pman ta' ni xa kay la nagamit, napa gani iyang thermal paste sa heatsink nga nka porma ug circle XD. Cge lang kay kung di ghapon mada ako nlng ni iuli npa ma'y wrranty XD Thanks guys.

[CARLOtech]

hehe very time you use your thermal paste pls change the stocks kay mogahi na init na dayun kaayu...

[bim27142]

Thanks, Tried all ur suggestions na mga bro. Pero mao japon. Di man unta ni ingani, ni kalit man lang. Good as new pman ta' ni xa kay la nagamit, napa gani iyang thermal paste sa heatsink nga nka porma ug circle XD. Cge lang kay kung di ghapon mada ako nlng ni iuli npa ma'y wrranty XD Thanks guys.

ipa warranty nalang siya bro para sure...

[goldfinger]

Tried that sa akong first AM2 processor when using stock HSF mo abot ug 70C over pa then shutdown, then ako gi ilisan ug CM CPU Cooler na ok ok pero mo shutdown gihapon occasionally then I found out naa jud diay issue ang processor cguro naka cause kay ESD kay overlook lang baya nato ang mag handle sa processor.... Lisod na bro labi na processor ang issue. IF warranty pana pailisi na nila ang processor kaysa mag antos paka.

[erwin_rommel]

grabeha pod anang 90-100 deg C oi mura na man nag binukal nga tubig. dapat di na mo bluescreen imo pc pero mo shutdown gyud og kalit unya wait pa ka og time before ma on na nimo og balik kay need pa pabugnawon. na try nimo og hikap ang heatsink? kay if ana nga temp, ma paso gyud ka ana if hikapon nimo ang heatsink.

[cursememore]

Nag photoshop ra q kadyut nia after pla lang ka seconds mao nani aqng temp

102°C , dmd na ako nlng jd ni dad.on saqng gpalitan.

[weezur]

if it's properly secured, is it possible nay daut sa thermal sensor?