Sleeving your psu.. and other wires.. DIY.(Do it yourself!!) ...

[anatanium]

---

I just want to share on how to sleeve your cables, specialy the psu(power supply)..with paracord... there are other materials aswell that you can use for sleeving.. its preferential, but then again i choose the paracord due to the fact that it is cheap.. and has a very fine braid....
why sleeve those cables/wires?? well for me.. those fcking wires are damn ugly!!

so.. to start.. things that you will need...
1.Paracord.. 2.hair pins ^_^ 3.some tapes.. 4. scissors.. 5. lighter(i find the torch or butane lighter easier to use pero pede sad solane or prycgas then sa stove...)

the hairpin.. you can buy these stuffs.. at the drug store..^_^ or if your having problem to get some.. then order them from e bay... this is what it looks like..
you're going to straighten these hairpins...after that use some fine sandpaper to remove the paint, and make it more thinner..


now the paracord.. the paracord has some stuffing inside.. that you will have to remove.. in order to make way for your wires..



now to remove the wires on the connector.. just slide in the hairpins from the sides.. as shown on the picture.. its better to use a little bit of pressure on those pins.. so a pair of pliers will be handy..



after that..just pull the wire from the other side.. and it should go out nicely ^_^


now to sleeve the wire.. you will have to tape the tip of the wire.. as shown on the pics.. its because the edges on it will create some restriction while your inserting it to the paracord...



as shown on the pics.. the tip is out of the paracord end... remove the tapes, use a lighter to burn the ends of the paracord.. making it shrink.. and hold its ground onto the wire tip.. making a very solid grip...



after that stretch the chord as much as you can....from the tip where you melt the ends of the chord.. until you reach the other end of the wire.. and determine its length ... cut the excess and stretch again to give it a snug fit into the wires inside..

melt the ends.. again ^_^ and were almost done..


after that.. we will have to bend those locks on the tip... as shown on the pic... those spikes will hold the wires or the pin inside the housing..



inserting the sleeved wire...on to the 8pin housing..




and you're done ^_^ happy sleeving
i didnt use shrink tubes.. cause i dont like it... it looks like sht.. with those on...



share lang ko ha? pasensya eh... kng d kau nindot ang pag ka buhat sa tutorial.. woah tog na ko ^_^

daghan man nangutana asa ma palit ang paracord... so.. if theres a place you want to go? im the one that you should know... im the map im the map .. ^_^ cbu doc hospital na near fuente osmeña.


additional paracord sellers 9 pesoses daw per foot... pangutan ah si Happyboy ^_^

[dlareG]

i learned that from youtube, hahaha, and i dont really like paracords, dali siya mu bati kung masangit aw, pirting batia.

[anatanium]

i learned that from youtube, hahaha, and i dont really like paracords, dali siya mu bati kung masangit aw, pirting batia.

unsa man say gi sangitan? kutsilyo? hahaha so far ok raman ang paracord.. para nako hehe

[dlareG]

aw ambot oi, ako man gi try ang paracord sa una, pero pag taod taod, ambot asa to nasangit, hahaha, pero try pud ang mga laing Sleeving like, MDPC, REN, FTW sleeves para di lang Paracord ang mapilian sa ubang istoryan

[renaire33]

nice guide bai ^_^
nindot jd ang paracord kay close kaayo, solid ang colors pero cloth like lang, in the long run ug sige tag tang2 taod, ma run na cya like any other cloth

[bim27142]

tempa, unsa ng paracord? hahaha! og asa na ma palit? mas maayo kanang maski asa ra commercially ma palit (like the hairpin ) para pure DIY gyud...

nindut ni nga guide kay DIY kaayo no need na mamalit og Mod tools nga usahay mahal2x ra ba og lisud pangitaon...

[andrex]

Asa mana ma palit nang paracord? Nindot lage ni pwede ra diay hairpin. Suwayan nya ni nako ba. TS share pud sa PSU to sata power unsaon pag sleeve nila.

Nya asa pud ta maka palit mga sleeve diri aside from paracord.

[keropi]

@anatanium
dili ba baga kaayo gamiton ng hairpin bro? ako gamit is staple wire.

[anatanium]

Asa mana ma palit nang paracord? Nindot lage ni pwede ra diay hairpin. Suwayan nya ni nako ba. TS share pud sa PSU to sata power unsaon pag sleeve nila.

Nya asa pud ta maka palit mga sleeve diri aside from paracord.

DIPINDI ra kng unsa nga sleeve imo gamiton.. paracord works for me.. ren sleeve kay renaire.. or at pinoyrigs.. wich is at 16pesos per foot.. paracord is 12 per foot.. wa pa ko ka suway sa sata...kay sa akong casing nga gi buhat ma tago man ang sata.. so wala ko ni mind...

- - - Updated - - -

@anatanium
dili ba baga kaayo gamiton ng hairpin bro? ako gamit is staple wire.

hmm gi lihaan nako gamay aron ma tang tang ang paint.. og gi pa nipsan pa gamay gyud.. mao hairpin ako gamit kay flat naman siya daan..

[anatanium]

you can buy those paracord @ Alphasource.. near cebu doctor dapit... tag 12pesoses ^_^ per foot
othere sleeves @ pinoy rigs,comcam,renaire that is called ren sleeves.. @ 16pesos ^_^ per foot