Overclocking 1333 to 1600

[scrawnykid]

---

Changed the voltage and the FSB ratio.

Mao ni siya ang changed values after editing BIOS.




Sakto na ni siya?

Thanks d.i sa tanan ni tabang.

[Sempron Guy]

imo timings bro la nagkadimao set it to 9-9-9-24

[KH0UJ]

imo timings bro la nagkadimao set it to 9-9-9-24

second da motion ko bro hehehe

9-9-9-24-41-2T <<<<

kana TS noticeable na kada click nuh? maski lu-ag pa na nga timings, samut pa gyud inig takdo na ana

happy tweaking bro

memory benchmark dayon bro i-compare ang 1333 default timings ug factory timings 1600, post some screenies pud TS ha para information sad sa uban nato nga ka istoryans

i neglect lang to akong gi post nga corsair RAM kay CAS 8 series to, CAS 9 na ang imuha (Long live corsair users hehehe)

[scrawnykid]

imo timings bro la nagkadimao set it to 9-9-9-24

second da motion ko bro hehehe

9-9-9-24-41-2T <<<<

kana TS noticeable na kada click nuh? maski lu-ag pa na nga timings, samut pa gyud inig takdo na ana

happy tweaking bro

memory benchmark dayon bro i-compare ang 1333 default timings ug factory timings 1600, post some screenies pud TS ha para information sad sa uban nato nga ka istoryans

Sirs, asa na dapit sa bios, unsa ako bantayan ana?

Ako man gisuwat tong 9-9-9-24 na nakit.an nako sa RAM stick nako pero wa ko kabaw asa ibutang sa BIOS.

[KH0UJ]

Sirs, asa na dapit sa bios, unsa ako bantayan ana?

Ako man gisuwat tong 9-9-9-24 na nakit.an nako sa RAM stick nako pero wa ko kabaw asa ibutang sa BIOS.

[balipseyev]

I auto lang ng imuhang timings bro... 9-9-9-24 man mugawas ana... sakto naman na, na timing...

[KH0UJ]

I auto lang ng imuhang timings bro... 9-9-9-24 man mugawas ana... sakto naman na, na timing...

mao ni iyang auto detect timing karon bro, lu-ag pa na nga timing kay ang Factory timing kay 9-9-9-24-41-2T @ 1.5 volts

[simoko]

change it to 9-9-9-24 AND LEAVE the 1T (CR) as is...

the CR(Command per Clock) setting determines the delay(in clock cycles) between the chip being selected and the mem controller beginning to send commands...performance is ALWAYS better in 1T...2T is only use/enabled if you have issues w/ your mem controller affecting stability labi na if you are using 4 sticks of rams w/c is not your case...

[scrawnykid]

change it to 9-9-9-24 AND LEAVE the 1T (CR) as is...

the CR(Command per Clock) setting determines the delay(in clock cycles) between the chip being selected and the mem controller beginning to send commands...performance is ALWAYS better in 1T...2T is only use/enabled if you have issues w/ your mem controller affecting stability labi na if you are using 4 sticks of rams w/c is not your case...

Sirs, nakit.an na nako ag DRAM Timing. Pero if ako itry to set it with something aside from Auto naay 3 choices mugawas;

DCT 0
DCT 1
Both

Pareha ra man ang mugawas na settings like ang mga CL, tRCL mangawas pero unsay difference ana nila 3?

[werty]

mas advantage sa AMD ang tighter timings compared to higher FSB. but if ma combine nmo ang duha mas labing maayo.