Istorya.nets overclockers league-Post your OC's Here. Read first post plz.

[Generals]

---

when not overclocked, is there much diff between the performance of an E6300 and E4300?

[[DSX]]

dugay na ko wa ga overclock.. my system's been running for only 2.8
ni try ko karon gabii and this is what i've got so far: i still need to do some tweaks though.

validation link here

[emoners]

@[DSX]: Nice OC bro! :mrgreen:

[[DSX]]

wheee!!! 12 hrs stable!

Validation link here

Lowest Idle Temp: 34C Avg: 35C
Highest Load Temp: 54C Avg: 51C
Load temp to Idle temp in about 10 secs

[muzikfreakah]

Way to go DSX! Feels good!!!!!!! Great job man! Ako wala pako ka stab test kay busy with personal stuff, will try by the end of the week

[[DSX]]

Haaaay brings back the good old OC days!!!

i have my e4300 running at 333fsb x 9, this is my daily rider, ~3GHz. 36idle, 45load (lesser if Aircon is on).... using gigabyte 3d rocket II

lemme grab some screenies. wala ko ka try ug push futher because im lazy... i dont know pilay max OC ako ma achieve ani. i have this baby running 24 x 7 provided walay brownouts mao nga i settled with this speed. i will push it a little more.
i traded my E6400 to a 4300, di man gud mu OC ako migo... fits him better.

well i'm still actually using my e6300 right now. my e4300 is still coming. the only reason i bought the e4300 is it is cheaper and that it has a greater multiplier. Also, i am planning to go quad core in a couple of months. the newer DS3 revision 3.3 has better power management. ako lang dili ganahan aning DS3 is that MEM speed is tied to the FSB. suya ko sa ako bro in law sa iya 680i kay pwede ma isolate ang MEM speed while increasing FSB (pero mas taas ko OC niya heheh watercooled pa siya pero dili siya kaabot 3.3 stable.)RMA pa niya iya board kay naay problema ang 680i nga dili maka overclock kung quad core.
karon i think fsb limited ko. do you notice any difference in performance granting same ang frequency?

[muzikfreakah]

hehehe, sige bro, go sa OC club. gamay ra man kaayo ang percentage sa ako overclock bro, ~9% ra, hehehe!


[img width=438 height=500]http://img337.imageshack.us/img337/7449/systeminfohd6.jpg[/img]

http://img337.imageshack.us/img337/7...teminfohd6.jpg



insect111

Please add a CPUZ validation link for this entry to be included on the list

[muzikfreakah]

@ceejay, OC na balik bai, whats your board ba?

Checkout first post for official istorya OC LIST!

[muzikfreakah]

@DSX Bai, 35C at 80% OC? Thats amazing. what cooler are you using again? mines running now at 3014.11mhz, orthos priming for 4 hours now at 62C (aircon, and an electricfan blowing right on the side panel. I dare not burn this in at 3400mhz Murag kailangan gyud watercooling lolz ;-D

[[DSX]]

@DSX Bai, 35C at 80% OC? Thats amazing. what cooler are you using again? mines running now at 3014.11mhz, orthos priming for 4 hours now at 62C (aircon, and an electricfan blowing right on the side panel. I dare not burn this in at 3400mhz Murag kailangan gyud watercooling lolz ;-D

yup. sometimes its even 1C lower than case temp. im using Thermaltake Big Typhoon and an ExTremEngine 3T Casing with a 250mm side fan. Mao na nga usually ang CPU temp is usually equal to case temp.

samot na sa E4300. Bago ra abot ang e4300 and the GA-965P-DS3 rev 3.3 board. Im currently running at 3Ghz case temp 35. CPU temp 20 wakekekek. dili pa ko ka orthos kay wala pa ma cured ang AS Ceramique. temp shoots up to 64 @ max load