RC flying

[borgia]

---

Hi I sell rc heli's and parts... you may visit my forsale thread:

https://www.istorya.net/forums/collec...pter-bnew.html

[blutac89]

ingun ko nimu sa una its better to fly it with no upgrades.hehe Basin nagka bali na ug taod imung motor, blade links. etc. complicated man na gud i.setup ang co-axial. naa lng mabali ug taod di na maka lupad....

ang 4 in 1 mu green pa man kaha ang LED?

yes green paman. All I did was to install new motors nya did it one by one man Motor A for A blades and B for B blades nya ang pag butang sa 4 in 1 receiver sa mga motors.

I thought nga super strong ra kaayo ang Se 180 extreme motors. karon pag taud naku sa stock motors mao ra gihapon mag ikid ikid naman sya.

Maybe a few fine tuning ra pud. Kung naa ka time palihug nya ko check hehehe....

btw ang esky ni sugot sa min amount hehehe i'm placing new orders now...

[blutac89]

na bundak man gud na hehehe

[blutac89]

i checked the motors sakto gyud ka bai na bale taud didto sa 4 in 1 controller. Ako nuon gi install balik ang se extreme 180 motors and correct config and now it's excellente..... stable na but na bali gyud mga landing gear front and rear hehehe naa ka reserves?

[ohnj67]

Hi Borgia,

Kumusta na?, naa naka 3d foamy plane?, soroy unya kog balig fampark, or if you and your friends have time to go to SRP on sunday morning around 7am, you can see a lot of foam airplanes, all
brushless, and see it fly. some are home made and some are kits, para managhan sad ta mag pa lupad ug foamies, Kay hapit na ang May compitition sa Srp, ang mga taga Dumaguete daghan kaayo nag pa lupad ug mga foam planes, Dili man mahal ang airplane and easy to build, ones ma guba ang plane, you can easity repair it without spending a lot , just use epoxy 5, and in minutes walah, fly again.
Regard nalang

[bittel]

ohnj67,

i have a foam plane. recently got lang. tried flying it last sun sa srp but kusog ra kaayo ang hangin. u mention naa pud mga kits, where mu kuha sa mga kits? and if home made, where do you buy the foam? and how about the hardwares like hinges, rods, motor mount, wheels, etc. where do you buy them exactly? or home made lang pud? i would like to make one na home made pud ta. kana lang gud typical profile ep foam plane. maybe you can give some suggestions. thanks

[blutac89]

thanks for the time ganiha derrick, it was fun and challenging gyud labi na pwerte kusuga sa hangin. sensya na daghan ayo mi ganina. close pa gyud fam park. basin ugma open na hehehe.

[Tarmac]

Robby,

Your bipe should be perfect at Family Park.

As far as EPP foam is concerned, murag lisud. Pero kung depron-type foam (XPS) imong gusto, kanang mga profile type aircraft ra (like my ill-fated CAP 232), sayon ra kaayo. Naay mga foam board sa National Bookstore. Just make sure to peel off the paper kay bug-at man. I'm thinking of buying next week so I can make my own design profile foamie to replace the CAP, and finally put my electric motor and ESC to work.

You will need to reinforce these with carbon fiber rods or strips. These, along with control horns, linkages and other hardware are available at Duck R/C. Puwede man ta mag order.

Here's an example of a depron foamie.

This DualSky Breeze Pro, by the way, is available at Duck R/C. Around PHP1,800 man tingali, unya naa pa nay discount. Barato ra ang motor ug ESC kay 6 amps ra man. Battery 300 mah lang.

Check out this website for free plans: FREE PLANS

[borgia]

lan, wai blima ganina welcome mu tanan! I dont know tom if open... abi gali nako open ganina wala diay.hehe But mag lisod gyud ang coaxial heli did2 if mu hangin. salamat sa dinner.hehe

John, cge lng gihapon ko fly heli. I went to srp last sunday. it was fun.

thanks!

[Tarmac]

Derrick,

Na ayo nako ang CopterX gahapon, thanks to parts contributions from Jack and Justin. Pero 4 pm na nako nahuman ug ayo. Larga ko Bacolod ugma, lupad unya ta inig balik nako.