2009 Overclocking Competition

[box2joe]

---

hehehe.. amo d i na xa. hmmmmm..... thanks kaayo sa mga explanation mga guros. dili jud d i na kakompyansahan kana nga error. i also searched sa internet then most cases got thier procie fried on the firts promt of the error. ganahan lang ko makasabot kung unsa jud tong TRAP error mao nag ask ko kay wala kaayo ko kasabot sa ako nabasahan sa net. anyway so far wala paman ko nakasulay ana.. my 100% OC e2140 runs for about 4-8 hours a day. @ 1.4VCore volt as what iv read from the net most of the e2140 runs stable @ 1.4 volts. ako kaliggan kay y taas kaayo xa ug need to be stable on 3.2oc while i manage to hit 3.0ghz oc using only 1.28VCore volt stable

[fineupgrades]

it's now Official, the OC competition is now OPEN!!!! Please check this link:https://www.istorya.net/forums/fine-u...ml#post3803686

[vashtinone]

Official na jd tawn.. pero sayang dli ko kaapil kay bati ako mobo... huhuhu..

[muzikfreakah]

Well sir I must say, its not all about the mobo you know and you have lots of time pa

[poldopunk]

hehehe.. amo d i na xa. hmmmmm..... thanks kaayo sa mga explanation mga guros. dili jud d i na kakompyansahan kana nga error. i also searched sa internet then most cases got thier procie fried on the firts promt of the error. ganahan lang ko makasabot kung unsa jud tong TRAP error mao nag ask ko kay wala kaayo ko kasabot sa ako nabasahan sa net. anyway so far wala paman ko nakasulay ana.. my 100% OC e2140 runs for about 4-8 hours a day. @ 1.4VCore volt as what iv read from the net most of the e2140 runs stable @ 1.4 volts. ako kaliggan kay y taas kaayo xa ug need to be stable on 3.2oc while i manage to hit 3.0ghz oc using only 1.28VCore volt stable

we share the same dilemma box2joe. mine needed 1.5v to get it to post and complete superpi at 3.2GHz but there's one thing i noticed, vdrops are getting way out of hand as you increase it. i can get mine to post at 1.48 but the voltage drops to 1.45 ~ 1.44 during load and it has to be within 1.46volts to avoid errors, unfortunately, it occasionally goes down to 1.45 which causes one core to error during 64-bit prime95.

i'm looking into GTL settings to obtain stability. gamay nalang jud tweak kulang para makuha nako ang 3.2GHz bisan 1.47 ~ 1.48, i'd still take it.

[JIGS]

OT:mga guru's pwede ba nako e oc ako proc is phenom 9600 and mobo is gigabyte GA-MA78GM

[box2joe]

@ poldopunk: unsaun nimo pagmonitor kung unsa nga core ang kinahanglan sakaan ug voltage sa GTL setting? mura kapoyan naman ko cge tag-an... tag-an gud...

[poldopunk]

here's an excellent article regarding Gunning Transceiver Logic:

Global

If you take a look at the example at the latter part of the page, there are 2 instances of overclocking at the same speed and the same voltage, the latter was stable with tweaks on the GTL settings which lasted for ~13 hours on prime95 until it was stopped.

Sa prime95, mo start baya na siya ug worker threads, where the number of threads depends on the number of cores, from here alone you'll know which one is the cause of fault since naa man mogawas nga error when the cpu is stressed.

Ang akoa lang problem ron kay sa BIOS, naka set man gud ang GTL settings to core 0 and core 1 then for quads, core 2 and core 3. If i make changes on the settings, ma apektohan ang core 1 pero wa pa ko kabalo kung ma unstable ba siya.

di pa ko ka test ron kay i'm preparing my rig for Wndows 7 Beta.

[dmelsie]

OT:@ poldo nindot ang windows 7 ganahan ko labi na sa ila explorer naay libraries system mao ni ako gipangita sauna....... pero beta pa sad lage pwede pa lahi niya sa official release
mao man ako tig gamit gamit ron....... license beta hehehe

[simoko]

@ poldopunk & box2joe: switch off the other core sa inyong procie para ma minimize ang problem sa Vdroop & u won't need a lot of voltage to make it stable...