TAMIYA MINI 4wd IS BACK !!!- See for Race Schedules

[RoOtsRoCk]

@moris bro ok ra guro ng rollers bisag unsa basta with o ring lang then 17 or 19mm jud ang sukod. suggestion lang kay mo sabut ta sa ubang newbie

sakto pud bro.....pero bsag dili lang 17mm ug 19mm kay naa man gud uban brand na dili 17 ug 19mm basta lang kay naay oring.....daghan pud raba wala nag oring wala pa 2 sila nakabalo ani.....wawa pud sila/kami...hehehe

[Merman]

@moris bro ok ra guro ng rollers bisag unsa basta with o ring lang then 17 or 19mm jud ang sukod. suggestion lang kay mo sabut ta sa ubang newbie

est php 1,200 for 3 sets tamiya rollers (19mm or 17mm) VS est php 600 for 3 sets auldery 19mm rollers.

darn! QQ!

but ara na mu kick in ang quality tamiya in the long run!

[tgetz]

pero atu pud sila e advise nga kung naa na sila xtra money mag hinay2x nalng sila palit ug tamiya rollers.

[mors311]

ATTENTION! Revision

ALL TAMIYA/SPEED TECH RULES:
1. Untampered Motor tamiya only (plasma,hyper 2, jet dash, ultra dash,atomic,torque)
2. Propeler shaft should be 8 teeth
3. pinion 8 teeth
4. Max 6 rollers 17mm or 19mm with o-ring (any brand will do)
5. Gears should only be tamiya only
6. Rear pin brakes only
7. Batts 700mah
8. Wheels tamiya only (wala nay lain)
9. Rear sliding bumper (pwed ra katong frp)


That's all folks

[tgetz]

ATTENTION! Revision

ALL TAMIYA/SPEED TECH RULES:
1. Untampered Motor tamiya only (plasma,hyper 2, jet dash, ultra dash,atomic,torque)
2. Propeler shaft should be 8 teeth
3. pinion 8 teeth
4. Max 6 rollers 17mm or 19mm with o-ring (any brand will do)
5. Gears should only be tamiya only
6. Rear pin brakes only
7. Batts 700mah
8. Wheels tamiya only (wala nay lain)
9. Rear sliding bumper (pwed ra katong frp)


That's all folks

Kani! Perfect ni!!!

[Merman]

^^ oh yeah!!!!!!!!!

[clydetuyz]

Kani! Perfect ni!!!

kani murag ni gaan akoang paminaw...

[TechnoCurse]

On the brightside, nindut man pod all tam. nindut man pod feeling makatag-iya tag all tamiya hehe. Hinay hinay lang tag tigum ani!

Sa All tamiya na SpeedTech, naa unta koy suggestion na Rules and Regulation, just like the official Tamiya rule, kaning "1.1.3 Machine Measuring System", since all tamiya naman jud ang items.

3. Machine Measuring System

Maximum Car Width: Under 105mm
Overall Car Height: Under 70mm
Overall Car Length: Under 165mm
Minimum Ground Clearance: At least 1mm
Minimum Car Weight (including batteries and motor): At least 90g
Front and Rear Tires: Diameter: 22-35mm, Width: 8-26mm (Note that tires must be attached.)
Rollers: Maximum of 6 installations total (double rollers count as 1 installation. Stabilizer poles and mass dampers do not count at all)
Mass Dampers: Mass damper may not extend from the sides beyond the line formed by the guide roller poles.
Parts that combine a guide roller with a mass damper will count as 1 roller installation.

[TechnoCurse]

ATTENTION! Revision

ALL TAMIYA/SPEED TECH RULES:
1. Untampered Motor tamiya only (plasma,hyper 2, jet dash, ultra dash,atomic,torque)
2. Propeler shaft should be 8 teeth
3. pinion 8 teeth
4. Max 6 rollers 17mm or 19mm with o-ring (any brand will do)
5. Gears should only be tamiya only
6. Rear pin brakes only
7. Batts 700mah
8. Wheels tamiya only (wala nay lain)
9. Rear sliding bumper (pwed ra katong frp)


That's all folks

Nice ni bro! Murag okay nani sa kadaghanan!
Suggest pod ko, ang placing sa Screws, dapat kanang dili maka carve sa track floor, dili makadamage, so to sum up ang hait na part sa screw's direction is upward.

[tgetz]

On the brightside, nindut man pod all tam. nindut man pod feeling makatag-iya tag all tamiya hehe. Hinay hinay lang tag tigum ani!

Sa All tamiya na SpeedTech, naa unta koy suggestion na Rules and Regulation, just like the official Tamiya rule, kaning "1.1.3 Machine Measuring System", since all tamiya naman jud ang items.

3. Machine Measuring System

Maximum Car Width: Under 105mm
Overall Car Height: Under 70mm
Overall Car Length: Under 165mm
Minimum Ground Clearance: At least 1mm
Minimum Car Weight (including batteries and motor): At least 90g
Front and Rear Tires: Diameter: 22-35mm, Width: 8-26mm (Note that tires must be attached.)
Rollers: Maximum of 6 installations total (double rollers count as 1 installation. Stabilizer poles and mass dampers do not count at all)
Mass Dampers: Mass damper may not extend from the sides beyond the line formed by the guide roller poles.
Parts that combine a guide roller with a mass damper will count as 1 roller installation.

ayaw nalng ni bro dili lang sa ta mo restrict ani may lang ni kung tamiya na jud ang mag pa race nya mga bigatin na ang mga sponsors..