galibog ko sa ddr2 1066 ug ddr3 1066

[simoko]

Team xtreem dark pc2-8500 actually ok na kaau cya ron pero gi set nako ang voltage to 2.08v i try ni nako og change later tonight.

ang main nako nga problem is sa bios and memory frenquency nga ma detect is 800 only but my ram is capable of 1066.

if its Team Xtreme Dark(TEDs) then DerFuhrer is right...taas na ang 2.4v...most TEDs use ProMos chips....if u have the old Team Xtreme then u are lucky...they use Micron D9 chips...mine here(DDR2-800 part# TXDD2048M800HC3DC) can go as high as 1180MHz at 5-5-5-15 timings 2.6V...

try to adjust the mem dividers to get 1066 at the least voltage, tightest timings u can get from your TEDs...basta stable lang payts na...

[Mrpitoy]

Bro,

DDR3's prefetch buffer width is 8 bit, whereas DDR2's is 4 bit, and DDR's is 2 bit.

Ang prefetch buffer is a memory cache located on modern RAM modules which stores data before it is actually needed.

DDR3's will increased operation frequencies, decreasted heat production by 30% (as promised kuno sa mga manufacturers - which actually depende sab on other factors, casing, fans, cooler, etc), will increase latency, increase bandwidth.

in short bro, DDR3's has less power consumption and higher bandwidth than DDR2. Just be smart to pair the right hardware para mapuslan nimo ang functionalities ani.

[limes]

asa ta maka palit ug ram na ddr2 1066?

[zhadlp]

bisag asa bro, daghan man available, different brands pa...

[fineupgrades]

asa ta maka palit ug ram na ddr2 1066?

On stock mi sir, OCZ Platinum Edition 4GB (2x2GB) DDR2 1066 Dual Channel Kit (CL 5-5-5-18 ). Check lang sa Interpace-Countrymall or Asia Pacific Computers-Emall

[Kenshiro]

So ok pa diay na ang 2.3v? or above sa DDR2 1066?

[limes]

On stock mi sir, OCZ Platinum Edition 4GB (2x2GB) DDR2 1066 Dual Channel Kit (CL 5-5-5-18 ). Check lang sa Interpace-Countrymall or Asia Pacific Computers-Emall

unsay pinaka barato na ddr2 1066? kay ako pa ni i dispose ako 2gb na ddr2 800 kingston.

[reishoto]

So ok pa diay na ang 2.3v? or above sa DDR2 1066?

depende ni sa model ug brand bro... kingston runs at 2.2v 1066 at cl5. if auto na nimo sa other motherboards, it runs at 1.8-1.9v at 800. though usually, 2.3v is already an OC voltage, gipataas na para mudagan mas paspas ang memory.

[limes]

depende ni sa model ug brand bro... kingston runs at 2.2v 1066 at cl5. if auto na nimo sa other motherboards, it runs at 1.8-1.9v at 800. though usually, 2.3v is already an OC voltage, gipataas na para mudagan mas paspas ang memory.

so ang tanan nga rams na ddr2 1066 kay gi overvolt ra? or naa jud standard na mao jud iya normal?

[reishoto]

nop, depende man gud na sa chips na gamit and design technology gigamit sa manufacturers bro. some DDR2 1066 runs normally at 2.2v, some at 1.8 or below. mao na gyud usahay dili mudawat ang uban motherboards sa ubang klase sa memory becuase of voltage requirements nga dili kaya ihatag sa board. some may run may at lower speeds than its specs.