how to change from bridge type to router connection?

[donix]

---

saon pag usab sa akong dsl connection from bridge to router type? sa modem raman daw? speedstream modem. pldt.

[Tamblot]

Before tweaking your modem, make sure you have access to its management console or GUI.

Ask assistance from your ISP if you have problems with it. Sometimes its better to let them do the job than doing the dirty job yourself. unless you plan to play around with that modem which i suppose is still the property of your ISP.

good luck!

[afortaliza]

I am just confused, you are using SpeedStream modem right? And that is Globelines not PLDT. I don't know if PLDT has Speedstream modem, most of their modem are Zyxel P-660R-D1 Router, PL-DSL1 Router, Prolink H9300G ADSL2+ Router, DB108/DB120/Alcatel ADSL HomePLusPlus Router.

And if your modem, is Zyxel P-660R-D1 Router then you have to follow this step by step configuration.

Note: Test it in a stand alone settings. Meaning, direct connection from PLDT router to your PC.

You may need to set a static IP address on your computer first before you can access the web config... (you know how to do that right?)



computer IP: 192.168.1.33
subnet mask: 255.255.255.0
default gateway: 192.168.1.1

save settings and reboot...

after restarting, on your web browser type 192.168.1.1

Username: admin
Password: 1234

then follow the screenshots to guide you...


this is the status page when in bridge mode... take note of VPI / VCI value here and use it on the next configuration page...

################################################## ##
################################################## ##

[img width=500 height=460]http://i224.photobucket.com/albums/dd182/LinkSysAdmin/routinghq9.png[/img]


go to Network / WAN / Internet Connection TAB

metro-manila area

Mode: Routing
Encapsulation: ENET ENCAP
Multiplexing: LLC
VPI: 0
VCI: 100

provincial area

Mode: Routing
Encapsulation: ENET ENCAP
Multiplexing: LLC
VPI: 0
VCI: 35

then click Obtain an IP Address Automatically

click Apply

if unsure about your VPI/VCI settings in your area, call 172 and ask...

################################################## ###
################################################## ###

[img width=500 height=460]http://i224.photobucket.com/albums/dd182/LinkSysAdmin/lanrb3.png[/img]

go to Network / LAN / IP TAB

IP Address: 192.168.1.1
IP Subnet Mask: 255.255.255.0

click Apply

################################################## ###
################################################## ###

[img width=500 height=460]http://i224.photobucket.com/albums/dd182/LinkSysAdmin/dhcpfl8.png[/img]

go to Network / LAN / DHCP Setup TAB

DHCP: Server
IP Pool Starting Address: 192.168.1.100
Pool Size: 32

click Apply

optional:
you can also enter your preferred DNS server if you want like OpenDNS...

OpenDNS Servers
Primary: 208.67.222.222
Secondary: 208.67.220.220

################################################## ###
################################################## ###

[img width=500 height=460]http://i224.photobucket.com/albums/dd182/LinkSysAdmin/natkn9.png[/img]

go to Network / NAT / General TAB

check Active Network Translation (NAT)
check SUA Only

click Apply

################################################## ###
################################################## ###

[img width=500 height=484]http://i224.photobucket.com/albums/dd182/LinkSysAdmin/restartwm8.png[/img]

go to Maintenance / Tools / Restart TAB

then restart to make the new configuration take effect...

################################################## ###
################################################## ###

[img width=500 height=484]http://i224.photobucket.com/albums/dd182/LinkSysAdmin/statusrouterhi9.png[/img]


after restarting, you can check the status page of your modem to verify the settings...

the screenshot above is what your status page should look like when in router mode...

the System Status is already in routing mode, and the Device Information now shows your IP address, Subnet Mask, and Default Gateway and the DHCP server is now active...

above values are just an example, you could set your own values like in IP starting address and pool size, etc...

after this, you can change your computer back to Dynamic IP Address if you like...



above screenshots were taken from a working connection... that means if it doesn't work for you, it's either you are doing something wrong or you didn't follow the guide completely...

if it doesn't work out, try hard resetting your modem, hold the reset switch at the back of your modem for a few seconds then try following the guide again...

[donix]

thanx kau bro! pldt ko bro, speedstream

[donix]

bro speedstream ako modem. dili plug and play ako modem, kinahanglan pako mu dial para maka net. saon pag usab ani nga diretso na??

[mr_glenn]

pag globelines na lang dong hehehe

[IT]

ayaw pagtuga=tuga ana dong... did u read the terms and conditions before you signed sa ISP. i think not

[v2s13]

Wa giahpon na sa sulbad don!?? Ako kay guba japon akong pldt 2 weeks na. ako nani ipa putol karn wednesday. hehe

[ka pedro]

ask lang ko mga bro naa man ko dsl modem brand is db108 adsl2+ modem,,dugay naman ni unya naputol naman ang line niya ..q: pwede pa ba siya magamit wala namn iya password ug user name??

[gustercaed]

bro speedstream ako modem. dili plug and play ako modem, kinahanglan pako mu dial para maka net. saon pag usab ani nga diretso na??

usb na imo modem bro? if yes dili na pwede. pailisan gyud na nimo ug lain na modem. kana i connect sa imo LAN card. walay lain way. kung ang purpose nimo maka share internet. i share nalang imo connection. imo lang pc server.