All about woodworking

[blotot]

@ waterboy

Bro unsa man imo opinion about sa depth sa closet/built in cabinet...pwedi ba siya 1 FT? para maka cut kog 4 cuts sa ako plywood?
or gamay ra/mabaw ra gyud ang 1 FT...Or 16 inch gyud pero 3 cuts lang?

Pls advice brader...ikaw man gyud na a TECH know how ani bahina...

[-kobe-]

@ KObe..

Bro about CS...when you buy I suggest you look @ the wattage...the higher the more RIP power...ako gyud before I go sa pinaka ka gamay wattage kay save sa electricity pero wa mag hunahuna sa max capabilty sa tool..



Just bought this last monday...@ Belmont....naka bundle ni with 4" angle grinder...very good price...bahala na x2 ang presyo basta SAFETY lang...kay na man gud unta pod low end na jackson cut off pero wa stock tag 4K ra...nya wa ta kabalo kon mo longtad ba...kani EAG for my weekend project murag overkill man gani pero cge nalang....

Safety issue brader....kay di ko sure sa ako safety everytime I use the angle grinder to cut my metals...plus with the cut off I could chop my pipe and angle bars in just CHOP...sa grinder mag lubag lubag pa kay its only 4" blade against the 14"...but the downside....kuryente...from my 650wtts to 2300 wtts...but saves a lot of time....in which I dont have much to spare...I only work on sundays...

nice kau ni sa metalworks..labi na pinakyaway hihihi..

nagamit ba ni nimu sa kahoy bro?

[waterboy0911]

@ waterboy

Bro unsa man imo opinion about sa depth sa closet/built in cabinet...pwedi ba siya 1 FT? para maka cut kog 4 cuts sa ako plywood?
or gamay ra/mabaw ra gyud ang 1 FT...Or 16 inch gyud pero 3 cuts lang?

Pls advice brader...ikaw man gyud na a TECH know how ani bahina...

Kung built in closet standard depth is 62 but usually para maka tipid 60 ang depth or 58cm..

Ang kanang 1ft kay pang kitchen cabinet mana kanang wall cabinet..

In addition:

Any furniture with a height over 4ft. Must have anti tip kit.. It's a law that most but not all furniture manufacturer neglect..

Try to research about 32mm system.. Most hafele or blumm hardware uses same standards..
Their is a little difference using other brands so check on the hardware dimensions too before boring holes for the hardware..
Most 32mm uses chip boards with melamine face and back.. So the thickness have a huge difference so instead of using 9.5mm, just use 9mm instead because most of us use 18mm thick plywood..

If you guys have questions regarding 32mm system.. Just ask but before you ask, be sure to research first..

[-kobe-]

@ waterboy

Bro unsa man imo opinion about sa depth sa closet/built in cabinet...pwedi ba siya 1 FT? para maka cut kog 4 cuts sa ako plywood?
or gamay ra/mabaw ra gyud ang 1 FT...Or 16 inch gyud pero 3 cuts lang?

Pls advice brader...ikaw man gyud na a TECH know how ani bahina...

wa jud ku kasabot ani ui,,tabang,,..aku nahibawan putol kay putol raman..naa d i nay standard nga sukod?

[-kobe-]

@waterboy..bro galibog jd nuon ku ani da,,mas maau guro pasabton mi nimu gamay,,kapoy basa english gd nya d kau nato masabtan..

[nodols3]

ga gamit sad ko miter saw.. Trimmer or router pwede For bevel cuts

ok raba ang skil nga brand sa router bro? or naa ka lain ika recommend nga dili parehas ka mahal sa makita or bosch? Usually naa diri mga barato2x kay fixed based man.

[blotot]

Kung built in closet standard depth is 62 but usually para maka tipid 60 ang depth or 58cm..

Ang kanang 1ft kay pang kitchen cabinet mana kanang wall cabinet..

In addition:

Any furniture with a height over 4ft. Must have anti tip kit.. It's a law that most but not all furniture manufacturer neglect..

Try to research about 32mm system.. Most hafele or blumm hardware uses same standards..
Their is a little difference using other brands so check on the hardware dimensions too before boring holes for the hardware..
Most 32mm uses chip boards with melamine face and back.. So the thickness have a huge difference so instead of using 9.5mm, just use 9mm instead because most of us use 18mm thick plywood..

If you guys have questions regarding 32mm system.. Just ask but before you ask, be sure to research first..

I am so blessed that I ask you BRO...mao gyud ni dapat nako mahibaw an...I been measuring closets kon mo check in ko sa mga hotels og kanang mo visit ko sa mga model houses sa mga housing...so now its very clear...

Thanks a lot bro.

- - - Updated - - -

ok raba ang skil nga brand sa router bro? or naa ka lain ika recommend nga dili parehas ka mahal sa makita or bosch? Usually naa diri mga barato2x kay fixed based man.

TRY daw check AEG brader...almost 2HP ang power niya...and good price....

[blotot]

Happy Easter.

Mao ni ako nahimo sa Holy week mga Brader...

BBQ biznez for summer...



Og Doll House para sa ako Daughter...



Sorry dili lagi ni woodworks...medyo na addicted ko sa welding karon...hheheh..

[nodols3]

I am so blessed that I ask you BRO...mao gyud ni dapat nako mahibaw an...I been measuring closets kon mo check in ko sa mga hotels og kanang mo visit ko sa mga model houses sa mga housing...so now its very clear...

Thanks a lot bro.

- - - Updated - - -



TRY daw check AEG brader...almost 2HP ang power niya...and good price....

Naghuna2x bitaw ko ani bro. Kaso gi bash man ang AEG sa usa ka forum nga dili daw siya maayo nga brand itself. Coming from TTI company. Ang skil is murag subsidiary sa Bosch, which as we know maayo gyud nga brand. Maong naglibog if ok raba gyud ang skil. As what I'd researched, pang DIY budget gyud daw ang Skil.. don't know lang sa quality pud kaha ani.

[blotot]

@ nodols

Bro nka buy naka ROUTER? post pic niya if you can have one...