MSI Twin Frozr 250 gts 512mb

[LadYKilleR8520]

---

mybe dried up ang thermal paste sa card.. have you checked the card temps? is it still ok? if by any chance you could get it to run for a few minuites, you can run furmark.. run furmark to make the GPU heat up and check the temps..

click here -> FurMark 1.13.0 Released | Geeks3D

[zarcon.phut1986]

replace na ug ug thermal paste still not working.
dili na mo display... mag hulat ko days or weeks arun mo gana nasad xa balik

[siopao1984]

Electronics Parts and Products will always have a chance of failure. that card is several generations back

[zarcon.phut1986]

Electronics Parts and Products will always have a chance of failure. that card is several generations back

yeah ur ryt but still hoping someone can repair this

[Wadexx]

aw, maka DL ra jud d i unta ka ug software kai 1 hour or 2 gud mag on, unless wa na jud ni ni on since nag start ang topic.

Anyway, imo naman gi try ug lain PC diba? Wa gihapon? Murag patay na jud na TS. I think naay mo repair ana pero chances are very slim na ma ayo pa jud siya. Kanang e reflow siya kai basin nag cold solder ka tungod overheating ba.

[zarcon.phut1986]

aw, maka DL ra jud d i unta ka ug software kai 1 hour or 2 gud mag on, unless wa na jud ni ni on since nag start ang topic.

Anyway, imo naman gi try ug lain PC diba? Wa gihapon? Murag patay na jud na TS. I think naay mo repair ana pero chances are very slim na ma ayo pa jud siya. Kanang e reflow siya kai basin nag cold solder ka tungod overheating ba.

gtry na nako ug reheat ang chipset nya then gbutangan ug thermal paste... yes ni gana jud xa for couple of hours then nawala nasad iya display.
after a day or 2 ni gana nasad ang VC then na palong nasad wala nasad xa mo display but note the fans are still running.

[Wadexx]

Check pud ang PSU kai murag either nilang duha ang ni fail. Need ka ato single rail.

Kai ug mu gana2x pa siya, naa jud sa supply ang daot tingali. If wala gihapon murag magpa technician na siya. Naa tingali ta mga capable techies diri nga wala pa nitubag sa ilang inputs. huwat2x lang ta.

Kuan d i boss, bisan nagfail na imong VC, naay chance mag spin gihapon ang fan niya. Dli necessary nga na guba na, off na pud ang fans.

[siopao1984]

fail na lage na ang video card.

if u said na imo na ge reheat and mag ok cya then something is wrong na with the solder points.

now if u want na ipa ball machine na ang card yes ma repair na but the cost of having it repaired, might as well buy a new one.

only thing that i can think of is to sprinkle salt and holy water sa video card and wait for a miracle to happen.

[juks]

Familiar with the laptops og similar machines nga once magproblema ang video card i reheat ra? Yes mogana na siyag balik most of the times pero walay guaranty nga modugay imo use ana. Once the problem comes back after reheating it once, believe me magsige ra nag balik, reheat na pud ka till di na gyud magamit imo component. To end this and maybe costly on you part but for us practical, change your vc.

[zarcon.phut1986]

thanks all! I should need to buy a new one... for the meantime gamiton lang usa nato ang onboard arun magamit pa ang pc