Brief introduction
Unsa ang Local Area Network or LAN nga gitawag?
Local Area Network (LAN)
- A local area network (LAN) is a group of computers and associated devices that share a common communications line or wireless link. Typically, connected devices share the resources of a single processor or server within a small geographic area.
Gi grupo kini sa tulo (3) o daghan pa nga computer nga gi tawag nga workgroup.
Bag-O ta magsugod mao ni ang materiales:
1.
Cable - bulk Category 5, 5e, 6 or 7 cable (usually blue or white in color)
2.
Wire Cutters - to cut and strip the cable if necessary
3.
RJ45 Plugs
4.
RJ45 Crimper
Recommended:
* Wire Stripper
* Network Hub or Switch
Optional
* Cable Tester
Let start.
Wiring
Importante ang sako nga set-up sa mga wires. I'll provide guide kung unsaon ni pag buhat.
Paniti ang cable wire nga gamiton using a Wire Cutter nga ako gi ingon. Mao ni ang hitsura sa cable wire pagkahuman paniti.
Important: Make sure nga pariho ang tupong sa wire sa pag putod ug pag panit.
1. E atobang sa inyo ang pins sa RJ45,
and take note of this wire color combination.

White Orange

Orange

White Green

Blue

White Blue

Green

White Brown

Brown
*Straight through Connection.
2. Dikitdikita ang mga wires sama sa paka sunodsunod sa mga color nga naa sa picture sa igbaw.
3. Make sure nga tupong tanan anti e sulod sa mga buho sa RJ45 plugs.
4. Kung pagkita ninyo nga tupong na or ok na tanan, isulod ang wire ngadto sa tumoy sa pag dikit sa pin sa RJ45.
5. Crimped it using a crimping tool.
Note: Ayaw kaayo ipita ky tingalig mabuak ang RJ45 plug.
6. Buhata kini sa kada tumoy sa cable wires. Kung pila ang mga computers na ine-network, mao gihapon ang ihap sa cable wires nga butangan ug rj45 ug e crimped.
7. Kung mahuman na tanan. Plug the RJ45 to your network adapter located at the back of your computer. Buhata sa tanang computer.
6. Kuhaa ang Network Hub ug iplug na tanan mga wires.
Now your ready for the configuration.
First step, Right Click "My Computer" on your desktop, click properties. Navigate to Computer Name tab. Enter a computer name and a work group name. Look like this

This image has been resized. Click this bar to view the full image. The original image is sized 728x531.
Important: Buhata sa tanan nga computer, different computer name but with a unique work group name.
Second step, Right Click
"My Network Place" on your desktop, click properties. Naa moy makita nga
"Lan Connection" as shown on the image below..
Right click that Lan Connection and click on Properties.
Configure the TCP/IP Properties as shown on the image below.

This image has been resized. Click this bar to view the full image. The original image is sized 1024x768.
Sa properties, Migamit ko ug Class C IP addressing. You can also use Class A or B or D, depende na sa inyo. But commonly used is the class A addressing.
Next, buhata na tanan sa mga computer. Parihas ang prosiso.
Done!!
Make sure nakaswitch ang network hub o switch.
Now, unsaon pag test kung successful ang inyong gi buhat?
Instructions:
1. Click Start
2. Run
3. Type this one. "Ping 192.168.x.xx" excluding ". Ang x.xx mao na ang inyong gi butangan ug IP address nga usa sa mga computer.
4. Ingini ang response sa cmd.exe.
Your done!!
Buhata kini sa tanang computers to make sure nga nagkita o connected silang tanan.
----------------------------------------------------------------------------------------------------------
don't criticize what you don't understand, learn it.
----------------------------------------------------------------------------------------------------------