Fibre glass reinforced, 1 1/4" cut off wheels/disc for dremel/rotary tools 10pcs for 250php

[titaniumbox]

---

Bluetooth zigbee Emulator CC-Debugger Support 2540/2541/2530 Protocol

Description:
Support Software:
SmartRF Studio, SmartRF Flash Programmer, IEEE Address Programmer, PacketSniffer, PurePathWireless, more than 8051 versions of IAR for (including the latest z-stack protocol stack used 8.10), and so on!

Supported operating systems:
WINXP, WIN7

Support chips overview:
TI's CC with 8051 chips and the full range of multiple transceivers, as follows:

A. And simulation of chip can be programmed are:
CC1110, CC1111
CC2430, CC2431
CC2510, CC2511
CC2530, CC2531, CC2533
CC2540, CC2541
CC2543, CC2544, CC2545

B. Can be controlled by SmartRF Studio chip are:
CC1120, CC1121, CC1125, CC1175
CC1100, CC1101, CC110L, CC113L, CC115L
CC2500, CC2520

C. Can be used to program the chip PurePath Wireless
CC8520, CC8521
CC8530, CC8531


Programming download program, please use the latest version of the software. Setup_SmartRFProgr_1.12.7
download the following address:

http://pan.baidu.com/s/1hq7ma5Q

Package Includes:
1 x CC-Debugger Emulator motherboard
1 x 1.2 m long high-quality mini-usb data cable
1 x 20cm long gray cable 10p

Spoiler! 

[titaniumbox]

Orange Pi PC ubuntu linux and android mini PC Beyond and Compatible with Raspberry Pi 2

What's Orange Pi PC？

It’s an open-source single-board computer. It can run Android 4.4, Ubuntu, Debian, Rasberry Pi Image, as well as the banana pi Image. It uses the AllWinner H3 SoC, and has 1GB DDR3 SDRAM

What can I do with Orange Pi PC?

Build…

A computer
A wireless server
Games
Music and sounds
HD video
A speaker
Android
Scratch
Pretty much anything else, because Orange Pi PC is open source


Who’s it for?

Orange Pi PC is for anyone who wants to start creating with technology – not just consuming it. It's a simple, fun, useful tool that you can use to start taking control of the world around you.

Hardware specification:
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K
GPU:
•Mali400MP2 GPU @600MHz
•Supports OpenGL ES 2.0
Memory (SDRAM): 1GB DDR3 (shared with GPU)
Onboard Storage: TF card (Max. 64GB) / MMC card slot
Onboard Network: 10/100M Ethernet RJ45
Video Input:
A CSI input connector Camera:
Supports 8-bit YUV422 CMOS sensor interface
Supports CCIR656 protocol for NTSC and PAL
Supports SM pixel camera sensor
Supports video capture solution up to 1080p@30fps
Audio Input: MIC
Video Outputs:
Supports HDMI output with HDCP
Supports HDMI CEC
Supports HDMI 30 function
Integrated CVBS
Supports simultaneous output of HDMI and CVBS
Audio Output: 3.5 mm Jack and HDMI
Power Source: DC input can supply power, but USB OTG input don’t supply power
USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG
Buttons: Power Button(SW4)
Low-level peripherals: 40 Pins Header, compatible with Raspberry Pi B+
GPIO(1x3) pin: UART, ground.
LED: Power led & Status led
Key: IR input, POWER
Supported OS: Android Ubuntu, Debian, Rasberry Pi Image

Interface definition:
Product size: 85 mm × 55mm
Weight: 38g

Package Includes:
1 x Orange Pi PC

Spoiler! 

[titaniumbox]

ESP8266 serial WIFI Witty cloud Development Board ESP-12F module MINI nodemcu


Description:
This cheap and small Wifi transceiver is the perfect solution for home Automation and IoT applications. It can be the replacement of your NRF24L01, it can talk to your Wifi router directly through the UART MCU's (Rx, Tx).
The ESP-12 module is one of the most complete of the ESP family as it allows you to use biggest amount of pins of all of them. You can program this module to work stand alone with the Arduino IDE or with LUA as NodeMCU.
It has an LDR and a WS2812 led already on board for your projects. The board comes with a CH40 micro USB module to program it.

The ESP8266 highly integrated chip, including antenna switch balun, power management converter, so with minimal external circuitry. The system is equipped with ESP8266 manifested leading features are: energy saving VoIP quickly switch between the sleep / wake patterns, with low-power operation adaptive radio bias, front-end signal processing functions.
This version, the ESP8266-03 is one of the smallest versions of this module. It includes a built-in ceramic antenna.

Specifications:
LDR Light Sensor on board
WS2812 Led on board
3x tactile buttons (1x in the Witty board and 2x in theCH340 board)
Supports 3 modes: AP,STA,AP+STA
Dimensions: 24mm x 16mm
Micro USB connection for power and/or programming

Package Includes:
1 x ESP8266 serial WIFI Witty cloud Development Board ESP-12F module MINI nodemcu

Spoiler! 

[titaniumbox]

Microchip PIC24FJ32GA002-I/SP, 16bit PIC Microcontroller, 32MHz, 32 kB Flash, 28-Pin SPDIP

Details:
Family Name PIC24FJ
Package Type SPDIP
Mounting Type Through Hole
Pin Count 28
Device Core PIC
Data Bus Width 16bit
Program Memory Size 32 kB
Maximum Frequency 32MHz
RAM Size 8 kB
Number of PWM Units 5
ADC Channels 10
Number of SPI Channels 2
Typical Operating Supply Voltage 2 to 3.6 V
Number of Timers 5
Width 0.295in
Program Memory Type Flash
PWM Resolution 10bit
Number of UART Channels 2
Pulse Width Modulation 5(10 bit) (Compare/PWM)
Length 35.56mm
Dimensions 1.4 x 0.295 x 0.15in
Minimum Operating Temperature -40 °C
Timers 5 x 16 bit
ADCs 10 x 10 bit
Number of ADC Units 1
Maximum Operating Temperature +85 °C
Height 0.15in
Number of I2C Channels 2
Instruction Set Architecture RISC
ADC Resolution 10bit
Timer Resolution 16bit

Datasheet:
http://ww1.microchip.com/downloads/e...Doc/39881c.pdf

Package Includes:
Microchip PIC24FJ32GA002-I/SP, 16bit PIC Microcontroller, 32MHz, 32 kB Flash, 28-Pin SPDIP

Spoiler! 

[titaniumbox]

EP Solar Tracer EN MPPT Controller Communication Cable CC-USB-RS485-150U To PC

Description:
Communication cable CC-USB-RS485-150U USB to PC RS485 for
EP Solar Tracer Viewstar VS Landstar LS series Solar Charge Controller
PC communication cable
Model:CC-USB-RS485-150U
For LS-B ,Tracer-B,VS-B Controller

Package Included:
1PCS x EP Solar Tracer EN MPPT Controller Communication Cable CC-USB-RS485-150U To PC

Spoiler! 

[titaniumbox]

USB to ESP8266 Serial Wireless Wifi Module Development Board 8266 Wifi Adapter

Features: High speed CPU frequency Can be used as a serial port WIFI

Specifications: Condition: New Color: Blue Size: 4.8*3.5cm Weight: 5.4g

Package Includes: 1 x USB to ESP8266 Serial Wireless Wifi Module

Spoiler! 

[titaniumbox]

RXB12 433Mhz Superheterodyne Wireless Receiver Precise for Arduino/AVR

Product Features:
1. Receiver sensitivity reach -115dBm;
2. Operating frequency: 433.92 MHz;
3. Power supply voltage input range: 3.3V-5.5V;
4. Low power consumption, 5.0V @ 433.92MHz, 3.8-4.1mA; 5.0V @ 315MHz, 2.5-2.8mA; sustained data transfer rates to (Manchester Encoded) 2.4K of
5. Good selectivity and spurious radiation suppression, and easy through CE / FCC international certification;
6. Good local oscillator radiation suppression, multiple receiver modules to work together (ie, more than single income) and will not interfere with each other, used together does not affect the receiving distance.
7. Temperature range: -30-85 ℃ can work even in harsh ambient temperature;
8. 30*8.5*5 (mm).

Applications:
1. Car remote door switch (RKE);
2. Remote control door opener;
3. Wireless security alarm;
4. Wireless doorbell;
5. Wireless Controller;
6. A wireless data transmission.

Package Included :
1 x RXB12 433Mhz Superheterodyne Wireless Receiver Precise for Arduino/AVR

Spoiler! 

[titaniumbox]

ATMEGA48+NRF24L01+wireless Shield module SPI to IIC I2C TWI Interface

Specification:
Operating voltage: 5V
Hold time of Module receives the data: more than 2S
Hold time of Module sends data: more than 300s
Transfer rate: 50Byte / S (theoretical value)
I2C/TWI Address: 0x47 (decimal 35)
NRF24L01 Address: 0x34, 0x43, 0x10, 0x10, 0x01 (from low to high)
Size:44 x 23 x 12mm(L x W x H)
Color: Black
Net weight:6g
Package weight:16g

Package Included:
1 x ATMEGA48 + NRF24L01 Interface wireless module

Spoiler! 

[titaniumbox]

UM3561A UMC DIP-8 IC Three Siren Sound Generator

Datasheet:
HTTP 301 This page has been moved

Package Includes:
1 x UM3561A UMC DIP-8 IC

Spoiler! 

[titaniumbox]

USR-TCP232-2 Serial RS232 TO Ethernet TCP IP Converter Module

Product Description:
Serial RS232 to Ethernet TCP IP converter module, A easy way for connect RS232 equipment to Ethernet, can work at TCP Server, TCP Client Or UDP mode.

Feature:
Single, compact RS-232 to Ethernet Solution
Featured transparent data transmission media conversion for RS232 over LAN or WAN.
Bandrate RS232 300 ~ 256000 bps
Auto detected 10/100M High speed Ethernet
AUTO MDI/MDIX, Use crossover cable or parallel cable connection;
Versatile serial operation options: Virtual Com, TCP client, UDP, UDP server, TCP Server
Configuration by RS232 or Ethernet, free software available
Virtual COM driver for Windows NT/2000/XP/2003/Vista
Small size: (LxWxH): 90x34x17(mm).
Power: 5V DC

Package Includes:
1 x USR-TCP232-2 Serial RS232 TO Ethernet TCP IP Converter Module

Spoiler!