MOTHERBOARD, HARD DISK, VIDEO CARD, RAM, & LAPTOP REPAIR SPECIALIST

[blitz]

i have 5 units ibm xseries 200 mobos with capacitor problems.
would capacitor problems also bust the processor?
coz most of them had busted procs too.

[ruelnov]

No.

When capacitors give in, the hardware monitor chip automatically shuts off the system by asserting a RESET signal to the processor and other micro-controller chips.

If the processor becomes busted, then that's a failure of the thermal sensing circuitry (if that board is provided with one). Some low-end boards are not equipped with this functionality.

On motherboards equipped with fail-safe thermal sensors, the processor automatically goes to SLEEP mode on overheat and so procesor damage is prevented.

[blitz]

i'll bring in some of them within the week...

[Allanz_kie]

Bai,
Naa ko 20G HD. Makita sa device manager pero dili sa my computer sa windows. gisulayan nako format gamit ko startup disk. Run nako fdisk sige lang 0% completed. Magtingogtingog raba ang HD morag gakagot. Maau pa kaha ni? Mga pila sad bay para mabudgetan. If ok price anha ko sat.

Thanks

[inspector_ronan]

kadamo mo man paki ana . tawagi nala niyo mga bai kung interesado gud kamo.
GREENVALLEY PC DOCTOR
414-4278/ 09275193317

[ruelnov]

Naay service rates sa page 1 ani nga post.

5 to 7 out of 10 hard disk drives can be repaired successfully.

[drkhero]

sir nuel!

gud pm, nkatesting nmi ug change ug capacitor , & yes successful siya, mao gyud na cause sa hangups ug dugay pud mo start ang uban pc, nakatry pud mi ug change, nya after changing,naa error nga wla na keyboard not detected, could the cause be, oversoldering, or maybe nakadamage ug uban pisa? we used soldering iron & hot air kay pino man gud ayo

what could be the solution, naa pko 2 spare boards asus for p3(cuv4x-c) & ecs (k7s5a), pwede rani ilisan iya ps2 nga part sa ako 2 ka mobo? wla pmi ngtry kay gnina man lng giayo nmo, this board is from a close friend of mine, nya gmit nya sa blay for projects sa iya anak,

tnx sir!

[drkhero]

sir ruel!

sori, sa gadali type,, na tuod ko nkalimtan, naa ka board for p3? naa man gud ko processor ug mem, ug video diri, mao board nalng , nya pila pud? tnx!

sori sa first reply nko ;(

[ruelnov]

Yes, it's possible nga dunay na-damage when you replaced the capacitors. This is a highly-technical operation and very tricky esp. if you're not experienced in doing it.

In my first attempts way back, I screwed up 3 of my own boards in the process. But as in everything we do in life, practice makes perfect!

Then after you have replaced the capacitors, you need technical expertise and equipment/diagnostics software to be able to QC/verify that you did it right, and that every component on the board is functioning properly (such as Low-level Processor tests, DMA tests, Interrupt Controller tests, RTC tests, CMOS Integrity tests, SM Bus tests, PCI Subsystem tests,etc.)

Lisod kon magmata-mata ta anang board repair, so dapat kumpleto ka sa gamit (test equipment and low-level diagnostics software).

[ruelnov]

Regarding replacing the PS/2 port, you can try and see if it solves your problem. No harm in doing it, as long as you make sure dili ma-damage ang ubang parts sa board.

But in my experience, PS/2 port problems are normally caused by BIOS-related issues. And if after re-programming your BIOS the problem is still there, there's not much you can do about it because the PS/2 port controller is integrated into the chipset in most cases.

[drkhero]

ok, tnx sir ruel!

ako lng usa itry ug replace iya ps2 sa kboard ug mouse,naa man spare board, btw ,naa ka baligya nga board sa p3? my process is p3 733mhz, tested nmo ug ok gyud,using other boards, pila pud sir?

tnx au!

[tingloy05]

bai ruelnov: duol ra diay ta ug location bai, asa na VICTOR VILLAGE nyoha? sa 1 or 2? kay anha-on lng nya tak...nkoy ipatan-aw nmo na MOTHERBOARD bai....naa ba kay charge? if ipatan-aw ra nko if nba'y guba kay if naa kay ako ipa-FIX nmo...salamat bai...

[ruelnov]

tunga-tunga sa Victor 1 and Victor 2 bro. naa man toy sketch gi-post basin tua sa page 2 or 3 ani nga post.

dalha lang didto bai ugma naa ra man ko didto tibuok adlaw. walay bayad oi kon magpa-checkup lang, dili btaw ni panginabuhi ang akoa lingaw lingaw ra gud aron makatabang pod ta sa uban nga nagkinahanglan.

[drkhero]

halu sir ruel!

tnx au sa imo advice! first ko nagilis ug kboard/mouse port, k na sir, ngano kaha 2, hinoon ang 2 ka capacitor ako giilisan(using my old hinagpatan nga board),1500uF 6.3V, k na pagreboot gniha, wla na ma keyboard error,boot na sa normal, nya wla na hangups ug restart lng kalit kay nailisan naman ang capacitor! ngdula pa gni ko gnina sa nbalive ka 2, ok na gyud, dli pareho sa una nga dli katiwas sa 2nd quarter, hangup or reset dyon, magmit na nila ila pc, its nice to be of great help gyud para sauban!

Sa tanan members sa istorya.net, tnx nin.u tanan, ug kang sir ruel,mao man gyud na mga cause sa hangups ug kana pud mokalit ug restart,

ako next prob, naa ko board diri sa ako migo nga atty. bisan sa bios palang, mo hungup na mga 20-40 secs lng, ako gicheck ang processor if sak2 ba,ug mga capacitor, so far wla man ko nakit.an physically, ambot kha ug naa pa gyud lain, chk nko ug balik 2ms puhon, unsa kaha lain ini sir ruel?

tnx again sir ruel, dont forget to pm f naa nka para p3 ha? ako ni gmiton ako old for linux!

[ruelnov]

Congrats for doing it yourself successfully! Sometimes, all you need is a brave heart and couple of advices.

For that other mobo with hang-up prob, mao nay gi-ingon nako nga dunay capacitor nga looking good externally (walay burot) pero tass na diay ang ESR. Kana, di na gyud na madala ug mata-mata bro.

Sometimes, this prob is caused by conflict in CMOS settings. So try clearing CMOS by moving the CMOS jumper while power is off, then ibalik ra dayon sa original position while power is still off.

If problem persists, you need a qualified serviceman na. But if you know how to flash the BIOS with a new image, that might solve the problem. But flashing is very risky unless you know how to recover your dead system kon ma failed upgrade. If not, that will render your system totally dead again.

Another possibility is corrupted memory module. Try replacing with a known good RAM.

Still another possibility is hinay ang tuyok sa processor fan or wala ba hinuon nituyok, or gamay ra ang imong heatsink mao nga mo-tagpilaw imong processor, hehe. Expermentohi lang bro before saying dili nimo makaya.