All about Smart Bro

[sagoy]

Ah, naglagot najud ko aning connection!

[harry547]

mga bro dri sa smartbro ask lang ta ko pila ang inyong makuha na latency/ping sa mga online games especially sa ran online ^^

[dexterdal]

Quote: Originally Posted by cloud Smartbro DNS Hijacjed by Akratz.com | Mike’s Technology Blog mao ni nga link bro plus kanang mga screenshot mu gawas gyud na siya bro instead of the site nga imo gusto.

thanks wla na na praning akong router, ok na sya. Thanks 2 u and sa Opendns

[acronis]

wala sad ko naka encounter ana.... try RESETTING the router, restore default settings, and configure settings all over again? or you could try borrowing a router from a friend and see if it works?

[cloud]

Quote: Originally Posted by rlcrl make sure nga imo'ng IP sa PC is 10.0.0.2 subnet 255.0.0.0 then do the arp -a

10.0.0.1 ra gyud, gkapoy na gyud kog sige balik balik mao ra gyud ang mo gawas sa "arp -a"

[cloud]

bro, sa mga wala nag router, kon mag ipconfig/all mo unsa ang inyo ip address? 192.168.xxx.xxx? pasabot ani naka private network na ang mga subscriber sa smartbro.

ip: 192.168.250.xxx
subnet: 255.255.254.0
gateway: 192.168.224.1
mao ni ang mu gawas sa ako. pasabot ani naka private address na ang smartbro.

[rlcrl]

Quote: Originally Posted by cloud 10.0.0.1 ra gyud, gkapoy na gyud kog sige balik balik mao ra gyud ang mo gawas sa "arp -a"

if that's the case, ang ip sa imo'ng canopy is still the default 169.254.1.1, so change your PC ip add to 169.254.1.2 subnet 255.255.255.0

then try entering 169.254.1.1 sa web browser

[cloud]

Quote: Originally Posted by rlcrl if that's the case, ang ip sa imo'ng canopy is still the default 169.254.1.1, so change your PC ip add to 169.254.1.2 subnet 255.255.255.0 then try entering 169.254.1.1 sa web browser

samot walay sulod ang arp table., dili sad ma ping ang 169.254.1.1 tried subnet 255.255.0.0 default sa 169.254.1.2 og subnet 255.255.255.0 same sa imo post. no result.

[rlcrl]

Quote: Originally Posted by cloud samot walay sulod ang arp table., dili sad ma ping ang 169.254.1.1 tried subnet 255.255.0.0 default sa 169.254.1.2 og subnet 255.255.255.0 same sa imo post. no result.

last option nimo is reset the canopy, kung gusto gyud ka maka access sa configuration...

duda ko nakasulod na ka sa una sa configuration niya?

tapos na enable ang dhcp so, wa gyud na lain option but to do a reset...

[cloud]

Quote: Originally Posted by rlcrl last option nimo is reset the canopy, kung gusto gyud ka maka access sa configuration... duda ko nakasulod na ka sa una sa configuration niya? tapos na enable ang dhcp so, wa gyud na lain option but to do a reset...

wala pa gyud kay bag-o lang man ni giilisan ang canopy kay gikotkot sa ilaga ang utp cable.

[rlcrl]

pwede sad nimo i-down ang canopy then convert the last 6digits of ESN to dec para makuha nimo ang ip address sa canopy...

kana kung gi-ilisan sa taga SmartBro ang IP kay SOP naman siguro gyud na nila... change IP from the default 169.254.1.1 to 10.x.x.x where x is the converted last six digit of the ESN

[bahiista]

mga bro..wa gyud moy laing mahimo ana..di gyud na kasolod unless reset ninyo inyo canopy IP...

[etgo]

try to reset your router.

[pepau]

Quote: Originally Posted by bahiista ##### sa tanan nga ganahan mo tweak sa ila canopy ####### here's a guide for you to override it so that you can change the settings again using the default IP ************************************************** **************************** **I WILL NOT BE RESPOSIBLE FOR ANY DAMAGES THIS MAY CAUSE YOU. USE IT AS YOUR OWN RISK!** ************************************************** **************************** This override plug resets the LAN 1 IP address to 169.254.1.1. The plug allows the operator to access the module through the default configuration without changing the configuration. The operator can then view and reset any non-default values. Acquiring the Override Plug To fabricate an override plug: 1. Install an RJ-11 6-pin connector onto a 6-inch length of CAT 5 cable. 2. Pin out all 6-pins. 3. Short (solder or twist together) Pins 4 and 6 on the other end. Do not connect any other wires to anything. The result should be as follows: Pin 1 → white / orange ← Pin 1 Pin 2 → white / green ← Pin 2 Pin 3 → white / blue ← Pin 3 Pin 4 → green ← Pin 6 Pin 5 → blue ← Pin 5 Pin 6 → orange← Pin 4 here's how you should number your RJ-11 6-pin socket.. http://img.photobucket.com/albums/v2...akers/rj11.jpg take note of the pins....save it pra dili ka makalimot.. hehehehe http://3.bp.blogspot.com/_N92lyDXZbz...w/s1600/DP.jpg pic of the actual jumper... http://img.photobucket.com/albums/v2...s/DSCN0529.jpg http://img.photobucket.com/albums/v2...s/DSCN0532.jpg ####this is where you connect the 4th and 6th pins or you design your own#### http://img.photobucket.com/albums/v2...s/DSCN0534.jpg http://img.photobucket.com/albums/v2...s/DSCN0536.jpg ###########Using the Override Plug########### The operator can regain access to the module as follows: make sure you unplug the power supply of the module 1. Insert override plug into the RJ-11 GPS sync port of the module. image: http://i34.tinypic.com/3449xcp.jpg 2. Apply power to the module through the Ethernet cable. RESULT: The module reboots with the default IP address of 169.254.1.1, password fields blank, and all other configuration values as previously set. 3. Set passwords as desired. 4. Change configuration values if desired. 5. Save the settings. 6. Remove the override plug. 7. Power cycle the module.

very nice sir...

[cloud]

ok nani bro, seguro tungod ni sa IP address sa smartbro nga 192.168.xxx.xxx nga naka private na.